How to Select the Right Zirconia Insert for Your Tundish Nozzle?
Oct 30, 2026
The zirconia insert sits at the heart of every tundish nozzle. It touches molten steel directly, takes the brunt of fast-flow scouring, chemical attack and sharp temperature swings. Pick the wrong grade, and you will see bore expansion, alumina clogging, thermal cracks, unstable casting speed and unplanned tundish stops. Many steel mills only compare piece price and overlook fit with actual casting conditions, which pushes up overall production cost. This piece breaks down practical selection points that our technical team uses when working with casting lines.
Match the Stabilized Zirconia Grade to Your Steel and Sequence Plan
The stabilizer and ZrO₂ purity set the baseline performance. This is where most teams get it wrong.
- Yttria-stabilized zirconia (YSZ, ZrO₂ 94–96%): Go with this for Al-killed steel, stainless, high manganese and other high-alloy grades. It resists molten steel wetting well, wears slowly and keeps bore size consistent through long sequence casting. Mould level fluctuation stays under better control.
- Magnesia or calcia partially stabilized zirconia (MgPSZ / CaPSZ): Better at handling thermal shock. We recommend it for plain carbon, low-carbon steel and lines with frequent start-stop, fast nozzle change cycles. It erodes faster than YSZ, so it is not a fit for extended high-alloy runs.
- Lower-zircon composite grades (ZrO₂ 70–85%): A cost-saving option only for short sequences, low-speed billet casting with limited slag attack. Do not use these for high pull speed or clean steel production.
One simple rule: higher ZrO₂ gives better erosion resistance, but usually makes the insert more sensitive to thermal shock. Do not just buy the highest purity available.
Check Physical Properties Beyond the Data Sheet
Do not sign off on a batch based only on the spec sheet. Track these key refractory indicators:
- Apparent porosity: Top performing inserts run at 10% or lower. Tight porosity stops steel penetration and slows alumina buildup. Higher porosity opens the door to internal erosion and clogging.
- Bulk density: Target 5.0 g/cm³ and above for premium grades. A denser fired body delivers longer service life.
- Cold crushing strength and retained strength after thermal cycling. We use a practical benchmark: keep at least 70% strength after thermal cycles, to avoid cracking during preheat or casting.
- Stabilization quality: Poor stabilization triggers phase change and volume shift. The insert can crack on its own with repeated heating and cooling.
Bore Geometry, Tolerance and Surface Finish Directly Affect Flow
Flow stability comes down to precision machining.
- Bore diameter and straight section length set your casting throughput. For billet and bloom metering nozzles, the length of the parallel section must match your casting curve to avoid jetting or swirling steel flow.
- Dimensional tolerance directly impacts concentricity and sealing between the zirconia insert, alumina-carbon outer shell and seat brick. Uneven contact creates hot spots and early spalling.
- Inner surface finish matters a lot for Al-killed steel. A smooth, well-finished bore cuts alumina sticking and reduces clog events.
We regularly supply custom profiles: straight bore, stepped bore and anti-swirl designs for slab, billet and bloom lines.
Map Out Your Site Conditions Before Sending an Inquiry
Gather these details first when talking to your refractory supplier:
- Steel grade (Al-killed, Si-killed, stainless, free-cutting etc.)
- Tundish operating temperature, hold time and target sequence heats
- Casting speed and how much pull speed normally drifts
- Preheating routine: lines with uneven or rushed preheat need grades built for thermal shock
- Nozzle system type: stopper rod controlled, fixed metering or quick-change slide gate. Stopper nozzles almost always use full high-purity zirconia inserts for fine flow adjustment.
We saw a real case from a carbon billet mill. They ran high-purity YSZ inserts and kept seeing cracking right after opening the cast. Switching over to MgPSZ stabilized zirconia removed the cracking, while still holding acceptable wear life.
Look at Total Cost, Not Just Unit Price
Lots of buyers fall for low upfront pricing. A cheaper insert that fails early means more nozzle changes, casting interruptions, ladle hold time and yield loss.
When comparing suppliers:
- Ask for batch MTR reports with full chemical and physical test results
- Confirm sinter consistency: powder quality, forming pressure and firing schedule change performance a lot between batches
- Confirm technical follow-up. A good supplier will track steel tonnage through each insert, log bore wear and adjust formulation if you keep seeing clogging or fast enlargement
- Lock in consistent supply if you run long continuous casting campaigns
Common Mistakes We See On Site
- Specifying ultra-high ZrO₂ for every steel grade, leading to repeated thermal cracking
- Ignoring bore finish and porosity for Al-killed steel, then fighting persistent alumina buildup
- Mixing tolerance standards. Poor fit between insert and outer shell creates leakage risk
- Using one single zirconia grade across all pull speeds and sequence lengths
- Running the same preheat cycle after switching material grades
The best zirconia insert is the one matched to your steel grade, thermal cycles and flow requirements. It is not the highest purity, and not the cheapest. Share your actual operating parameters clearly with your refractory partner. This cuts nozzle failures, extends casting sequences and keeps molten steel cleanliness steady.






